,Cathode Ray Tubes,Ceramic Tubes,CFA,chemical synthesis,chromenes,CO2 sensors,Communication,composite membranes,condensed heterocycles,Control Tubes,CWT,database,Devices,Diodes,Discharger,Display Tubes,Electron Tubes,Electron,antitumor,artificial organs,artificial skin,Attenuators,Audio tubes,Backward Wave Oscillator,Band filtering,Beam tubes,biocompatibility,biomaterials,biosensors,Broadcast,Broadcasting Tubes,Broadcasting,carbon dioxide isolation3CX300A1,4CX400A,4CX800A,4X150A,6360,6BK4,6BQ7.6C19,6C33C,6D22S,6N1P,6S19P,7034,813,829A,832A,833A,absorbent,Acquisition,Aircraft,Amateur Radio,Amateur,Amplifiers,Antenna amplifiers,anticancer compounds,antitumor agent,Broadcast Tubes,Transmitting Tubes,Transmitting,Broadcast,Russia,component,Navigator,product,characteristics,tube,technical,information,diagram">

GU-17

BEAM-POWER TETRODE

The GU-17 beam-power double tetrode is used for generation or power amplification at frequencies up to 250 MHz in RF equipment.

GENERAL
Cathode: indirectly heated, oxide coated.
Envelope: glass, miniature.
Height: at most 80 mm.
Diameter: at most 22.5 mm.
Mass: at most 25 g.

gu-17(1)1.jpg
1 - grid 1 of first tetrode; 2 - cathode and beam-forming plates; 3 - grid 1 of second tetrode; 4 - heater; 5 - heater; 6 - anode of first tetrode; 7 - grid 2; 8 - anode of second tetrode; 9 - heater (centre tap)

OPERATING ENVIRONMENTAL CONDITIONS
Vibration loads:
frequencies, Hz 20-600
acceleration, m/s² 59
Multiple impacts with acceleration, m/s² 118
Single impacts with acceleration, m/s² 490
Linear loads with acceleration, m/s² 294
Relative humidity at up to +40°C, % 98

BASIC DATA
Electrical Parameters
Heater voltage, V 6.3
Heater current, A 0.72-0.88
Mutual conductance (at anode and grid 2 voltages 200 V, end 1 voltage 16 V of first tetrode grid 1 voltage 100 V of 2nd tetrode), mA/V 1.6-3.3
Anode current (at anode and grid 2 voltage 200 V, grid 1 voltage 16 V of 1 st tetrode grid 1 voltage 100 V of 2nd tetiode), mA 10-30
Interelectrode capacitance, pF:
input 5.2-7.8
output 2.2-3.2
transfer, s, at most 0.1
Warm up time, s, at most 40
Output power (at anode voltage 300 V, grid 2 voltage 200V voltage 80 V of grids 1), W, at least 11
Output power over 400 h of service, W, at least 8.8

Limit Operating Values
Heater voltage, V:
with parallel-connected heater 5.7-7
with series-connected heater 11-14
Anode voltage, V 400
Anode voltage at the instant of switching on, V 450
Voltage between cathode and heater, V -150 to +150
Cathode current, mA 100
Dissipation, W:
anodes 12
grid 2 3
grid 1 0.5
Operating frequency, MHz 250
Envelope temperature, °C 260

gu-17(2)1.jpg
Maximum Permissible Anode Dissipation Pa max versus Ambient Temperature (at bulb temperature Tb 260 °C)